Fundamentals and explainers
Search by topic, standard, webinar title, product feature, or category. Use the search and filters to narrow the library, then open any card for the full article.
ADA 101
August 5, 2022
2010 ADAS 242.2 Swimming Pools At least two accessible means of entry shall be provided for swimming pools. Accessible means of entry shall be swimming pool lifts complying with 1009.2; sloped entries complying with 1009
Read more →
ADA 101
August 4, 2022
2010 ADAS 703.4.2 Location of Tactile Characters Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side. Where a tactile sign is provided at double doors with one activ
Read more →
ADA 101
June 7, 2022
2010 ADAS 1007.3.2 Golf Club Reach Range Area All areas within holes where golf balls rest shall be within 36 inches (915 mm) maximum of a clear floor or ground space 36 inches (915 mm) wide minimum and 48 inches (1220 m
Read more →
ADA 101
November 19, 2021
2010 ADAS Ambulatory Accessible Toilet Compartment Doors Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance betwe
Read more →
ADA 101
October 29, 2021
20210 ADAS 703.7.2.4 Assistive Listening Systems Assistive listening systems shall be identified by the International Symbol of Access for Hearing Loss complying with Figure 703.7.2.4. Citation according to 2010 ADAS. Ch
Read more →
ADA 101
October 15, 2021
2010 ADAS 703.7.2.3 Volume Control Telephones Telephones with a volume control shall be identified by a pictogram of a telephone handset with radiating sound waves on a square field such as shown in Figure 703.7.2.3. Cit
Read more →
ADA 101
October 1, 2021
2010 ADAS 703.7.2.2 International Symbol of TTY The International Symbol of TTY shall comply with Figure 703.7.2.2. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states such as California,
Read more →
ADA 101
September 17, 2021
2010 ADAS 703.7.2.1 International Symbol of Accessibility The International Symbol of Accessibility shall comply with Figure 703.7.2.1. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states
Read more →
ADA 101
September 10, 2021
2010 ADAS 703.4.1 Signs – Height Above Finish Floor or Ground Tactile characters on signs shall be located 48 inches minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile char
Read more →
ADA 101
September 3, 2021
2010 ADAS 608.5.2 Controls in Standard Roll-In Type Shower Compartments In standard roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 4
Read more →
ADA 101
August 27, 2021
2010 ADAS 610.3.1 Rectangular Seats The rear edge of a rectangular seat shall be 2 1/2 inches maximum and the front edge 15 inches minimum and 16 inches maximum from the seat wall. The side edge of the seat shall be 1 1/
Read more →
ADA 101
August 20, 2021
2010 ADAS 610.3 Shower Compartment Seats Where a seat is provided in a standard roll-in shower compartment, it shall be a folding type, shall be installed on the side wall adjacent to the controls, and shall extend from
Read more →
ADA 101
August 6, 2021
2010 ADAS 609.3 Spacing of Grab Bars The space between the wall and the grab bar shall be 1 1/2 inches. The space between the grab bar and projecting objects below and at the ends shall be 1 1/2 inches minimum. The space
Read more →
ADA 101
July 30, 2021
2010 ADAS 610.3.2 L-Shaped Shower Seat The rear edge of an L-shaped seat shall be 2 1/2 inches maximum and the front edge 15 inches minimum and 16 inches maximum from the seat wall. The rear edge of the “L” portion of th
Read more →
ADA 101
July 16, 2021
2010 ADAS 608.2.1 Transfer Type Shower Compartments Transfer type shower compartments shall be 36 inches by 36 inches clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch wide
Read more →
ADA 101
July 9, 2021
2010 ADAS 608.3.3 Alternate Roll-In Type Shower Compartments In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry. Grab bars sh
Read more →
ADA 101
July 2, 2021
2010 ADAS 608.3.2 Garb Bars in Standard Roll-In Type Shower Compartments Where a seat is provided in standard roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall opposite the
Read more →
ADA 101
June 28, 2021
2010 ADAS 608.2.2 Standard Roll-In Type Shower Compartments Standard roll-in type shower compartments shall be 30 inches wide minimum by 60 inches deep minimum clear inside dimensions measured at center points of opposin
Read more →
ADA 101
June 18, 2021
2010 ADAS 607.2 Bathtubs Clearance Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches wide minimum. A lavatory complying with 606 shall be permitted at the control end of the cle
Read more →
ADA 101
June 4, 2021
2010 ADAS 607.4.1.2 Bathtubs With Permanent Seats Control End Wall A grab bar 24 inches long minimum shall be installed on the control end wall at the front edge of the bathtub. Citation according to 2010 ADAS. Check you
Read more →
ADA 101
May 28, 2021
2010 ADAS 607.4.1.1 Bathtubs With Permanent Seats Back Wall Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and the other located 8 inches minimum and 10 inches maximum above the r
Read more →
ADA 101
May 21, 2021
2010 ADAS 604.8.2.1 Ambulatory Accessible Toilet Compartment Size Ambulatory accessible compartments shall have a depth of 60 inches minimum and a width of 35 inches minimum and 37 inches maximum. Citation according to 2
Read more →
ADA 101
May 7, 2021
2010 ADAS 505.10.3 Bottom Handrail Extension at Stairs At the bottom of a stair flight, handrails shall extend at the slope of the stair flight for a horizontal distance at least equal to one tread depth beyond the last
Read more →
ADA 101
April 30, 2021
2010 ADAS 505.10.2 Top Extension at Stairs At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches minimum beginning directly above the first riser nosing. Extensions shall retur
Read more →
ADA 101
April 23, 2021
2010 ADAS 505.7.2 Non-Circular Cross Sections Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches minimum and 6 1/4 inches maximum, and a cross-section dimension of 2
Read more →
ADA 101
April 16, 2021
2010 ADAS 306.2.5 Toe Clearance Width Toe clearance shall be 30 inches wide minimum. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states such as California, Georgia and Florida have additi
Read more →
ADA 101
April 9, 2021
2010 ADAS 306.2.1 Toe Clearance General Space under an element between the finish floor or ground and 9 inches above the finish floor or ground shall be considered toe clearance and shall comply with 306.2. Citation acco
Read more →
ADA 101
March 26, 2021
2010 ADAS 502.3.4 Access Aisle Location Access aisles shall not overlap the vehicular way. Access aisles shall be permitted to be placed on either side of the parking space except for angled van parking spaces which shal
Read more →
ADA 101
March 19, 2021
2010 ADAS 502.3.3 Access Aisle Marking Access aisles shall be marked so as to discourage parking in them. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states such as California, Georgia an
Read more →
ADA 101
March 12, 2021
2010 ADAS 502.3.2 Access Aisle Length Access aisles shall extend the full length of the parking spaces they serve. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states such as California, G
Read more →
ADA 101
March 5, 2021
2010 ADAS 502.3.1 Access Aisle Width Access aisles serving car and van parking spaces shall be 60 inches wide minimum. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states such as Californi
Read more →
ADA 101
February 19, 2021
ADAS 2010 405.7.3 Ramp Landing Length The landing clear length shall be 60 inches long minimum. Citation according to 2010 ADAS. Check your state’s accessibility laws. Some states such as California, Georgia and Florida
Read more →
ADA 101
February 5, 2021
2010 ADAS 405.7.4 Ramp Landing Change in Direction Ramps that change direction between runs at landings shall have a clear landing 60 inches minimum by 60 inches minimum. Citation according to 2010 ADAS. Check your state
Read more →
ADA 101
January 22, 2021
2010 ADAS 308.3.2 Obstructed High Side Reach Where a clear floor or ground space allows a parallel approach to an element and the high side reach is over an obstruction, the height of the obstruction shall be 34 inches m
Read more →
ADA 101
January 15, 2021
2010 ADAS 308.2.2 Obstructed High Forward Reach Where a high forward reach is over an obstruction, the clear floor space shall extend beneath the element for a distance not less than the required reach depth over the obs
Read more →
ADA 101
December 18, 2020
2010 ADAS 306.2.3 Toe Clearance – Minimum Required Depth Where toe clearance is required at an element as part of a clear floor space, the toe clearance shall extend 17 inches minimum under the element. Citation accordin
Read more →
ADA 101
December 4, 2020
ADAS 2010 303.3 Changes in Level – Beveled Changes in level between 1/4 inch high minimum and 1/2 inch high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled. A change in level of 1/2 inc
Read more →
ADA 101
November 20, 2020
2010 ADAS 302.2 Carpet Carpet or carpet tile shall be securely attached and shall have a firm cushion, pad, or backing or no cushion or pad. Carpet or carpet tile shall have a level loop, textured loop, level cut pile, o
Read more →
ADA 101
August 14, 2020
2010 ADAS 504.5 Stair Tread Nosings The radius of curvature at the leading edge of the tread shall be 1/2 inch maximum. Nosings that project beyond risers shall have the underside of the leading edge curved or beveled. R
Read more →
ADA 101
July 31, 2020
2010 ADAS 308.3.1 Unobstructed Side Reach Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches maximum and the low side r
Read more →
ADA 101
July 10, 2020
2010 ADAS 604.5.2 Rear Grab Bar at Water Closets The rear wall grab bar shall be 36 inches long minimum and extend from the centerline of the water closet 12 inches minimum on one side and 24 inches minimum on the other
Read more →
ADA 101
June 29, 2020
2010 ADAS 206.2.2 Accessible Routes Within a Site At least one accessible route shall connect accessible buildings, accessible facilities, accessible elements, and accessible spaces that are on the same site. Code accord
Read more →
ADA 101
June 26, 2020
2010 ADAS 604.8.1.2 Wheelchair Accessible Toilet Compartment Doors Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, cleara
Read more →
ADA 101
June 19, 2020
2010 ADAS 604.8.1.1 Wheelchair Accessible Toilet Compartment Wheelchair accessible compartments shall be 60 inches wide minimum measured perpendicular to the side wall, and 56 inches deep minimum for wall hung water clos
Read more →
ADA 101
June 12, 2020
ADAS 2010 604.5.1 Side Wall Grab Bar The side wall grab bar shall be 42 inches long minimum, located 12 inches maximum from the rear wall and extending 54 inches minimum from the rear wall. Code according to 2010 ADAS. C
Read more →
ADA 101
June 5, 2020
ADAS 2010 604.2 Water Closet Location The water closet shall be positioned with a wall or partition to the rear and to one side. The centerline of the water closet shall be 16 inches minimum to 18 inches maximum from the
Read more →
ADA 101
May 29, 2020
ADAS 2010 604.7 Water Closets and Toilet Compartments Dispensers Toilet paper dispensers shall comply with 309.4 and shall be 7 inches minimum and 9 inches maximum in front of the water closet measured to the centerline
Read more →
ADA 101
May 22, 2020
ADAS 2010 308.2.1 Unobstructed Forward Reach Where a forward reach is unobstructed, the high forward reach shall be 48 inches maximum and the low forward reach shall be 15 inches minimum above the finish floor or ground.
Read more →
ADA 101
May 15, 2020
ADAS 2010 602.5 Drinking Fountain Spout Location The spout shall be located 15 inches minimum from the vertical support and 5 inches maximum from the front edge of the unit, including bumpers. Code according to 2010 ADAS
Read more →
ADA 101
May 8, 2020
ADAS 2010 505.5 Handrail Clearance. Clearance between handrail gripping surfaces and adjacent surfaces shall be 1 1/2 inches minimum. Code according to 2010 ADAS. Check your state’s accessibility laws. Some states such a
Read more →
ADA 101
May 1, 2020
ADAS 2010 407.2.2.2 Elevator Signal Location. Visible signal fixtures shall be centered at 72 inches minimum above the finish floor or ground. The visible signal elements shall be 2 1/2 inches minimum measured along the
Read more →
ADA 101
April 20, 2020
ADAS 2010 404.2.4.1 Maneuvering Clearances at Manual Swinging Doors and Gates. Swinging doors and gates shall have maneuvering clearances complying with Table 404.2.4.1. Code according to 2010 ADAS. Check your state’s ac
Read more →
ADA 101
April 17, 2020
ADAS 2010 407.2.2.1 Elevator Visible and Audible Signals Visible signal fixtures shall be centered at 72 inches minimum above the finish floor or ground. The visible signal elements shall be 2 1/2 inches minimum measured
Read more →
ADA 101
April 10, 2020
ADAS 2010 410.6 Platform Lifts Doors and Gates Platform lifts shall have low-energy power-operated doors or gates complying with 404.3. Doors shall remain open for 20 seconds minimum. End doors and gates shall provide a
Read more →
ADA 101
April 3, 2020
ADAS 2010 503.3 Passenger Loading Zones Access Aisle Passenger loading zones shall provide access aisles complying with 503 adjacent to the vehicle pull-up space. Access aisles shall adjoin an accessible route and shall
Read more →
ADA 101
March 27, 2020
ADAS 2010 407.2.3.1 Elevator Floor Designation Floor designations complying with 703.2 and 703.4.1 shall be provided on both jambs of elevator hoistway entrances. Floor designations shall be provided in both tactile char
Read more →
ADA 101
March 20, 2020
ADAS 2010 305.5 Position of Clear Floor or Ground Space Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element. Code according to 2010 ADAS. Chec
Read more →
ADA 101
March 13, 2020
2010 ADAS 406.6 Diagonal Curb Cuts Diagonal or corner type curb ramps with returned curbs or other well-defined edges shall have the edges parallel to the direction of pedestrian flow. The bottom of diagonal curb ramps s
Read more →
ADA 101
February 28, 2020
2010 ADAS 404.2.3 Clear Width (Doors) Door openings shall provide a clear width of 32 inches minimum. Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the d
Read more →
ADA 101
February 21, 2020
2010 ADAS 307.3 Post Mounted Objects Free-standing objects mounted on posts or pylons shall overhang circulation paths 12 inches maximum when located 27 inches minimum and 80 inches maximum above the finish floor or grou
Read more →
ADA 101
February 7, 2020
2010 ADAS 308.2.1 Forward Reach Unobstructed Where a forward reach is unobstructed, the high forward reach shall be 48 inches maximum and the low forward reach shall be 15 inches minimum above the finish floor or ground.
Read more →
ADA 101
January 31, 2020
2010 ADAS 306.3.3 Knee Clearance Minimum Required Depth Where knee clearance is required under an element as part of a clear floor space, the knee clearance shall be 11 inches deep minimum at 9 inches above the finish fl
Read more →
ADA 101
January 24, 2020
2010 ADAS 306.2.3 Minimum Required Depth Where toe clearance is required at an element as part of a clear floor space, the toe clearance shall extend 17 inches minimum under the element. Code according to 2010 ADAS. Chec
Read more →
ADA 101
January 17, 2020
2010 ADAS 304.3.2 T-Shaped Space The turning space shall be a T-shaped space within a 60 inch square minimum with arms and base 36 inches wide minimum. Each arm of the T shall be clear of obstructions 12 inches minimum i
Read more →
ADA 101
January 10, 2020
2010 ADAS 304.3.1 Circular Space The turning space shall be a space of 60 inches diameter minimum. The space shall be permitted to include knee and toe clearance complying with 306. Code according to 2010 ADAS. Check you
Read more →
ADA 101
January 3, 2020
2010 ADAS 406.4 Curb Ramp Landings Landings shall be provided at the tops of curb ramps. The landing clear length shall be 36 inches minimum. The landing clear width shall be at least as wide as the curb ramp, excluding
Read more →
ADA 101
December 27, 2019
2010 ADAS 406.3 Sides of Curb Ramps Where provided, curb ramp flares shall not be steeper the 1:10 (10%). Code according to 2010 ADAS. Check your state’s accessibility laws. Some states such as California, Georgia and Fl
Read more →
ADA 101
December 20, 2019
2010 ADAS 403.5.5 Passing Spaces An accessible route with a clear width less than 60 inches shall provide passing spaces at intervals of 200 feet maximum. Passing spaces shall be either: a space 60 inches minimum by 60 i
Read more →
ADA 101
December 13, 2019
2010 ADAS 305.7.2 Clear Floor or Ground Space Parallel Approach Alcoves shall be 60 inches wide minimum where the depth exceeds 15 inches. Code according to 2010 ADAS. Check your state’s accessibility laws. Some states s
Read more →
ADA 101
December 6, 2019
2010 ADAS 305.7.1 Clear Floor or Ground Space Forward Approach Alcoves shall be 36 inches wide minimum where the depth exceeds 24 inches. Code according to 2010 ADAS. Check your state’s accessibility laws. Some states su
Read more →
ADA 101
November 15, 2019
2010 ADAS 405.7.1 Ramp Landing Slope Landings shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 (2%) shall be permitted. Code according to 2010 ADAS. Check your state’s ac
Read more →
ADA 101
November 8, 2019
2010 ADAS 305.3 Clear Ground Or Floor Space Size The clear floor or ground space shall be 30 inches minimum by 48 inches minimum. Code according to 2010 ADAS. Check your state’s accessibility laws. Some states such as Ca
Read more →
ADA 101
November 4, 2019
2010 ADAS 406.2 Counter Slope Counter slopes of adjoining gutters and road surfaces immediately adjacent to the curb ramp shall not be steeper than 1:20, 5%. The adjacent surfaces at transitions at curb ramps to walks, g
Read more →
ADA 101
October 25, 2019
2010 ADAS 405.9.1 Extended Floor or Ground Surface The floor or ground surface of the ramp run or landing shall extend 12 inches minimum beyond the inside face of a handrail complying with 505. Code according to 2010 ADA
Read more →
ADA 101
October 18, 2019
2010 ADAS 405.9.2 Curb or Barrier Edge Protection A curb or barrier shall be provided that prevents the passage of a 4 inch diameter sphere, where any portion of the sphere is within 4 inches of the finish floor or groun
Read more →
ADA 101
October 11, 2019
2010 ADAS 404.2.4.3 Recessed Doors and Gates Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches of the latch side of a doorway projects more than 8 inches beyond the face
Read more →
ADA 101
September 27, 2019
ADAS 2010 404.2.6 Doors in Series and Gates in Series The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches minimum plus the width of doors or gates swinging into the space. Co
Read more →
ADA 101
September 20, 2019
2010 ADAS 403.5.2 Clear Width at Turn Where the accessible route makes a 180 degree turn around an element which is less than 48 inches wide, clear width shall be 42 inches minimum approaching the turn, 48 inches minimum
Read more →
ADA 101
September 13, 2019
2010 ADAS 403.3 Walking Surfaces Slope The running slope of walking surfaces shall not be steeper than 1:20 (5%). The cross slope of walking surfaces shall not be steeper than 1:48 (2%). Code according to 2010 ADAS. Chec
Read more →
ADA 101
September 6, 2019
2010 ADAS 403.5.1 Walking Surfaces – Clear Width Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches minimum. EXCEPTION: The clear width shall be permitted to be reduced to 3
Read more →
ADA 101
August 30, 2019
2010 ADAS 309.4 Operable Parts – Operation Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate operable parts shall be 5
Read more →
ADA 101
August 23, 2019
ADAS 2010 307.4 – Vertical Clearance Vertical clearance shall be 80 inches high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches high. The leading edge of such g
Read more →
ADA 101
August 19, 2019
2010 ADAS 505.4 – Handrail Height Top of gripping surfaces of handrails shall be 34 inches minimum and 38 inches maximum vertically above walking surfaces, stair nosings, and ramp surfaces. Handrails shall be at a consis
Read more →
ADA 101
August 9, 2019
2010 ADAS 404.2.11 – Vision Lights Doors, gates, and side lights adjacent to doors or gates, containing one or more glazing panels that permit viewing through the panels shall have the bottom of at least one glazed panel
Read more →
ADA 101
July 31, 2019
2010 ADAS 404.2.10 – Door and Gate Surfaces Swinging door and gate surfaces within 10 inches of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the
Read more →
ADA 101
July 26, 2019
2010 ADAS 505.10.1 – Handrail Extensions at Ramps Ramp handrails shall extend horizontally above the landing for 12 inches minimum beyond the top and bottom of ramp runs. Extensions shall return to a wall, guard, or the
Read more →
ADA 101
July 19, 2019
2010 ADAS 307.2 – Protruding Object Limits Objects with leading edges more than 27 inches and not more than 80 inches above the finish floor or ground shall protrude 4 inches maximum horizontally into the circulation pat
Read more →
ADA 101
July 2, 2019
2010 ADAS 406.4 – Curb Ramp Landings Landings shall be provided at the tops of curb ramps. The landing clear length shall be 36 inches minimum. The landing clear width shall be at least as wide as the curb ramp, excludin
Read more →
ADA 101
June 5, 2019
ADA Title II 35.150 – Existing Facilities A public entity must operate each service, program, or activity so that the service, program, or activity, when viewed in its entirety, is readily accessible to and usable by ind
Read more →
ADA 101
May 22, 2019
ADA Title II 35.136 – Service Animals (a) General. Generally, a public entity shall modify its policies, practices, or procedures to permit the use of a service animal by an individual with a disability. (b) Exceptions.
Read more →
ADA 101
May 2, 2019
A DA Title II 35.163 – Information and Signage (a) A public entity shall ensure that interested persons, including persons with impaired vision or hearing, can obtain information as to the existence and location of acces
Read more →
ADA 101
April 4, 2019
2010 ADAS 502.2 – Parking – Vehicles Spaces Car parking spaces shall be 96 inches wide minimum and van parking spaces shall be 132 inches wide minimum, shall be marked to define the width, and shall have an adjacent acce
Read more →
ADA 101
March 25, 2019
2010 ADAS 303.2 – Changes in Ground Surface Level – Vertical Where changes in level are permitted in floor or ground surfaces, changes in level of 1/4 inch high maximum shall be permitted to be vertical. 2010 ADAS 303.3
Read more →
ADA 101
March 14, 2019
2010 ADAS 802.1.3 – Wheelchair Spaces – Depth Where a wheelchair space can be entered from the front or rear, the wheelchair space shall be 48 inches deep minimum. Where a wheelchair space can be entered only from the si
Read more →
ADA 101
February 27, 2019
2010 ADAS 802.1.2 – Wheelchair Spaces – Width A single wheelchair space shall be 36 inches wide minimum. Where two adjacent wheelchair spaces are provided, each wheelchair space shall be 33 inches wide minimum. Code acco
Read more →
ADA 101
February 19, 2019
2010 ADAS 242.2 – Swimming Pools At least two accessible means of entry shall be provided for swimming pools. Accessible means of entry shall be swimming pool lifts complying with 1009.2; sloped entries complying with 10
Read more →
ADA 101
February 5, 2019
2010 ADAS 604.3.1 – Size of Clearance at Water Closets Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular
Read more →
ADA 101
January 18, 2019
2010 ADAS 404.2.9 – Door and Gate Opening Force The force for pushing or pulling open a door or gate other than fire doors shall be 5 pounds maximum. The maximum force pertains to the continuous application of force nece
Read more →
ADA 101
January 11, 2019
502.3 – Off Street Parking Access Aisle Access aisles serving parking spaces shall adjoin an accessible route. Two parking spaces shall be permitted to share a common access aisle. Access aisles serving car and van parki
Read more →
ADA 101
January 4, 2019
ADA 302.3 – Expansion Joints Along Accessible Routes Openings in floor or ground surfaces will not allow passage of a sphere more than a half-inch in diameter. Check your state’s accessibility laws. Some states such as C
Read more →
ADA 101
December 27, 2018
ADA 206.2.1 – Accessible Site Arrival Points At least one accessible route shall be provided within the site from accessible parking spaces and accessible passenger loading zones; public streets and sidewalks; and public
Read more →No resources matched that search. Try a broader term or clear the filter.
